about us
news
products
heating
custom engineering
parts
resources
where to buy
contact us

 

Heating

QMark provides a wide range of electric, radiant and infrared heaters for residential, commercial and industrial use. Products range from specially designed heating units for installation in concealed spaces to garage heaters, baseboard heaters, unit heaters and more.

 

Baseboard heaters (Convector heaters) Portable heaters
Radiant heaters Wall heaters
Ceiling heaters Specialty heaters
Unit heaters Duct heaters
Wash down/ Explosion Pro  
 

>>> ST - Commercial Slope Top Convectors

 
Features
  • Provide total or supplemental heating for offices, corridors, lobbies, motels, apartments or similar facilities. Mounted under expanses of glass, they prevent cold down drafts.
  • With a range of heating capacities from 125 watts (435 BTU per hour) to 250 watts (852 BTU per hour) per foot length, these units can run from wall-to-wall or they can be mounted as discrete units in lengths of 28 inches to 10 feet.
  • The attractive 45º sloped top discourages use of heater as a shelf or a "step stool"
  • The unit is designed to mount on the wall at sill height (or lower) and can be positioned directly on the floor. The end of the unit can be positioned against adjacent sidewall if desired.
  • Standard finish is neutral grey. Also available in a spectrum of muted architectural colors in baked enamel finishes which are compatible with all interior decors.
  • Front cover is fabricated from 16-guage steel. While the back is constructed of 18-gauge. For service, all internal parts are accessible by removing cover Top of front cover engages with back; bottom of cover locks into place with screws.
  • Elements are long life metal sheath, aluminum fin type anchored to allow for quiet expansion and contraction.
  • Thermal limit switch with linear type (full length) sensing bulb provides constant protection against overheating from any cause. The switch will automatically reset when normal operating temperatures are restored.
  • Units are pre-wired. Units without optional controls are designed for either right or left hand entry for easy connection of supply wiring from bottom, rear or end, as well as multiple wiring of adjacent heaters from one entry point.
 
 
Specifications
CATALOG NUMBER LENGTH NOMINAL WATTS PER FT. TOTAL HEAT CAPACITY WATTS 120V AMPS 208V AMPS 240V AMPS 277V AMPS 347V AMPS 600V AMPS SHIP WT.(lbs.)
    125 250 2.1 1.2 1 0.9
ST02 28” 188 375 3.1 1.8 1.6 1.4 12 lbs.
    250 500 4.2 2.4 2.1 1.8 1.4
    125 375 3.1 1.8 1.6 1.4 1.1
ST03 36” 188 546 4.7 2.7 2.4 2 1.6 15 lbs.
    250 750 6.2 3.6 3.1 2.7 2.2
    125 500 4.2 2.4 2.1 1.8 1.4
ST04 48” 188 750 6.2 3.6 3.1 2.7 2.2 1.3 19 lbs.
    250 1000 8.3 4.8 4.2 3.6 2.9 1.7
    125 625 5.2 3 2.6 2.3 1.8 1
ST05 60” 188 940 7.8 4.5 3.9 3.4 2.7 1.6 24 lbs.
    250 1250 10.4 6 5.3 4.5 3.6 2.1
    125 750 6.2 3.6 3.1 2.7 2.1 1.3
ST06 72” 188 1125 9.4 5.4 4.7 4.1 3.2 1.9 26 lbs.
    250 1500 12.5 7.2 6.3 5.4 4.3 2.5
    125 1000 4.8 4.2 3.6 2.9 1.7
ST08 96” 188 1500 7.2 6.3 5.4 4.3 2.5 37 lbs.
    250 2000 9.6 8.3 7.2 5.8 3.3
    125 1250 6 5.2 4.5 3.6 2.1
ST10 120” 188 1875 9 7.8 6.8 5.4 3.1 45 lbs.
    250 2500 12 10.4 9 7.2 4.2

 

 

Qmark Engineered Products

470 Beauty Spot Road East 
Bennettsville, South Carolina 29512 
United States 
 

© 2014 Qmark Engineered Products